Aircraft Mechanic II

The Aircraft Mechanic II - Powerplant/Engine Back Shop Mechanic (T700/701C/D, T55-714) with experience in all three MDS UH60, CH47 & AH64 performs and inspects aviation unit ( AVUM ), intermediate ( AVIM ) and depot maintenance on assigned aircraft systems. • Perform maintenance and repair of major assemblies and subassemblies of the T700/701C/D, T55-714 and auxiliary power units. • Inspect engine turbine blades to detect cracks, distortion, corrosion, burn-out, security, or breaks. • Perform blade blending and blade replacement in cold section of powerplants. • Replace or repair worn or damaged components, such as generators, alternators, fuel controls, fuel pumps, oil pumps, and engine mounted gearboxes, and compressor bleed valves. • Ability to Perform hot section inspections and determine replacement of hot section components (GG rotors, stators, fuel injectors, igniters, power turbine.) • Disassemble and inspect parts for wear, cracks, security, or other defects. • Perform engine removal, replacement, reinstallation, and quick-change assembly (QCA) maintenance tasks. Minimum Requirements • High School Graduate or equivalent is required. • Five (5) years of recent applicable aircraft maintenance experience is required. • With A&P Two (2) years aviation maintenance experience, and Two (2) years' experience on MDS UH60, CH47, & AH64 is required. • Without A&P, must have Three (3) years aviation maintenance experience, Three (3) years rotary wing aircraft experience and Two (2) years on the assigned Mission Design Series UH-60, AH-64, CH-47 (MDS) to qualify. • All experience must be within the Five (5) most recent years. • Must be in possession of a Valid U.S. Passport for travel internationally. Passport must contain a minimum of 6 Blank pages and 2 years remaining before expiration date. • Ability to obtain/maintain a US Government Security Clearance (NAC-I T1) Public Trust. US Citizenship is Required to obtain a Security Clearance, and for facility access to this site. • Able to clear CENTCOM MOD Physicals requirement for deployment. (Attend CRC). • Must be able to obtain Kuwait Visa. Knowledge & Skills • General knowledge of aircraft mechanical component troubleshooting, repair procedures and replacement of parts. • Thorough knowledge of aircraft electrical and avionics component and system troubleshooting, repair procedures and replacement of parts. • Thorough knowledge of aircraft unique tools such as test equipment, torque wrenches, dial indicators, micrometers. • Working knowledge of technical publications and Logistics Information Systems. • Able to prioritize workloads to maintain schedules on assigned projects and is required to lead teams through more complex aircraft relevant tasks. • Possess the level of experience to inspect all required aeronautical type maintenance to be performed by Mechanics. • The incumbent receives technical guidance, as required, from supervisor or higher-level technician, will occasionally be required to lead teams through more complex aircraft relevant tasks, and may be required to make entries in aircraft logs and records. Physical Requirements/Working Environment • May work in aircraft maintenance hangar or outside. • May be required to respond to a wide variety of operational circumstances, including extreme weather conditions and rudimentary infrastructure. • May be exposed to extreme noise from turbine and jet engine aircraft. • May be exposed to fumes or airborne particles; may be exposed to electrical shock hazards or work near moving mechanical parts, vehicles, or aircraft. • Must be able to walk and stand on level and/or inclined surfaces for certain periods throughout the day. • Must be able to climb stairs, ramps, ladders, and work stands. • Must be able to crouch, crawl, grasp or handle objects, use finger dexterity, bend elbow/knee and reach above/below shoulders. • May be required to lift up to 50 pounds. • May be required to see aircraft in flight, read dials/gauges, identify small objects and hand tools. • Must be able to see imperfections, micrometer readings and other small scales. • Must be able to communicate by voice and detect sound by ear. • Must be able to distinguish color and judge three-dimensional depth. • May be required to operate power vehicles, machinery, hand tools, ground support equipment, fork lift, APU, etc.